The feeding method of asphalt mixing equipment is briefly described.

　　In the debugging, we should closely observe whether each motor corresponding to the instrument signal is normal, whether the Operation button can be used effectively, the operation of each motor rotation direction is correct, whether the motor can ensure that the operation of the belt does not occur deviation and skidding phenomenon.
Whether there is leakage in the cylinder work.
If a problem occurs, we should stop immediately and check for faults to ensure that the parts of the equipment are in optimal use.
If all the motors can function properly, we only enter the manual control for the no-load test run, when there are many conditions to meet the standards, in the automatic no-load experiment.

.

　　1.
Thermal regeneration
　　Thermal regeneration refers to the asphalt pavement in the process of regeneration of old materials need to be heated, and as required to add other regenerative additives, and then carry out other regeneration process.
Thermal regeneration can be divided into hot mix regeneration and in-situ heat regeneration.

　　(1) Because of the heavy workload of large asphalt mixing station, its floor area is very demanding.
To take full account of the types of equipment in construction and the storage of stone, we should try our best to choose in the middle section of the construction section, but also to take into account whether the source of water and electricity can be guaranteed, transport raw materials and finished materials in and out of the asphalt station is convenient transportation.

Working principle of asphalt mixing station
Asphalt, is a high viscosity organic liquid, the surface is black, soluble in carbon disulfide (a golden stench of liquid).
They are more likely to exist in the form of tar or tar.

.

　　① Hot Mix Regeneratio
>　　The Recycled asphalt Pavement material (RAP) is transported to the asphalt mixing plant (field, station), which is broken and screened, and mixed with a certain proportion with the new material, fresh asphalt, regenerative agent (if necessary) and so on to make hot mix recycled mixture to pave the road surface technology

>

>　　① Cold Mixing regenerati
/>　　The Recycled Asphalt Drum Mix Plant Pavement material (RAP) is transported to the mixing plant (field, station
/>After crushing, screening, to a certain proportion with the Xinji material, asphalt regeneration binder, active filler (cement, lime, etc.), water, such as mixing at room temperature, asphalt pavement regeneration technology paved at room temperatur

/>　　(3) In the case of simultaneous construction of multiple highways, the easiest way to choose the most suitable location is to calculate the various costs and determine the address through the average distanc

/>　　Asphalt concrete mixing building as an important equipment in highway construction, it will be mechanical, electrical and automation technology of a variety of technologies to collec
/>On the technical level, the maintenance of asphalt mixing building is a very important wor
/>In the construction of asphalt concrete mixed building referred to as asphalt building, its production capacity, control system automation degree and measurement accuracy, sewage treatment equipment energy consumption rate has become the main factor to measure the performance of asphalt buildin

/

/>　　After understanding the advantages and disadvantages of the two, it is easy to see how the asphalt mixing equipment model is loade
/>Of course, there is no limit to the way asphalt mixing equipment is fee
/>It is important to meet the needs of the configuration according to the needs of the customer and the investment of funds, and to choose the appropriate production mode and mode of operatio

/>　　The common feeding methods of asphalt mixing equipment are divided into two forms of hopper feeding and belt feedin
/>If you want to know the different ways of feeding, we need to know the difference between the two firs
/>The characteristics of hopper feed are low cost, small footprint, simple structure and fast feeding spee
/>The main material of belt is large conveying distance, high efficiency and low failure rat
/>Although the cost is high, the charging speed is much faste

/

/>　　In the geothermal regeneration to the asphalt pavement heating, milling, in situ mixed with a certain number of new bitumen and other regenerative agents, and then through the hot state mixing, paving, milling and other processes, so the unit is many and complex, the need for a combination of multi-clock units to carry out operations, the initial equipment investment is also large
/>The geothermal regeneration equipment can be divided into two kinds, such as compound mixing regeneration and resurfacing regeneratio

/

/>　　From the data released by the European Asphalt Pavement Association, the methods of asphalt pavement regeneration in Europe and America are mainly heat and temperature mixing, and the international Organization for Economic Cooperation and Development (OECD) survey on the recycling of pavement in 14 countries shows that (asphalt part), Hot mix regeneration (plant mixing heat regeneration) is a commonly used regeneration method, cold regeneration generally only accounts Other regeneration methods are also used in only a few countries.